1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C

1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C
1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C
1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C
1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C
1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C
1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C
1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C
1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C
1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C
1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C

1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C

1872×1404, 7.8inch E-Ink display HAT for Raspberry Pi, IT8951 controller, USB/SPI/I80/I2C interface. This is an E-Ink display HAT for Raspberry Pi, 7.8inch, 1872×1404 resolution, with embedded controller IT8951, communicating via USB/SPI/I80/I2C interface, supports partial refresh. Due to the advantages like low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as ebook reader, e-ink display, industrial instruments, and so on.

No backlight, keeps displaying last content for a long time even when power down. Low power consumption, basically power is only required for refreshing. Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards.

USB/SPI/I80/I2C interface, for connecting with host boards like Raspberry Pi/Nucleo, etc. Comes with development resources and manual (examples for Raspberry Pi/STM32). Outline dimension: 173.8mm × 127.6mm × 0.78mm. Display size: 158.184mm × 118.638mm. Dot pitch: 0.0845mm × 0.0845mm.

Gray scale: 2-16 (1-4 bit). Total refresh power: 1.2Wtyp. Total standby power: 0.1Wtyp. SPI chip selection, low active. Busy status output, low active. E-Paper IT8951 Driver HAT (B) Dimensions. 27.60 × 27.60. 48.0 × 33.0.

1.54inch e-Paper Module (B). 1.54inch e-Paper Module (C).

27.51 × 27.51. 48.55 × 23.71.

65.0 × 30.2. 2.13inch e-Paper HAT (B). 2.13inch e-Paper HAT (C).

2.13inch e-Paper HAT (D). 59.2 × 29.2. 57.29 × 38.19. 85.0 × 56.0. 2.7inch e-Paper HAT (B). 66.89 × 29.05. 89.5 × 38.0.

2.9inch e-Paper Module (B). 2.9inch e-Paper Module (C). 2.9inch e-Paper HAT (D).

66.90 × 29.06. 79.0 × 36.7. 84.80 × 63.60. 103.0 × 78.5. 4.2inch e-Paper Module (B).

4.2inch e-Paper Module (C). 4.3inch e-Paper UART Module. 88.00 × 66.00. 118.0 × 75.0. 118.8 × 88.26.

125.4 × 99.5. 5.83inch e-Paper HAT (B). 5.83inch e-Paper HAT (C). 122.4 × 90.6.

138.4 × 101.8. 163.20 × 97.92. 170.2 × 111.2. 7.5inch e-Paper HAT (B). 7.5inch e-Paper HAT (C). 158.18 × 118.64. 173.8 × 127.6. 202.8 × 139.43. 10.3inch e-Paper HAT (D). 209.66 × 157.25. 227.7 × 165.8. Standard Raspberry Pi header on module, allowed to be attached onto Pi directly, compatible with Raspberry Pi 40PIN GPIO extension header.

E-Paper IT8951 Driver HAT (B) x1. 7.8inch e-Paper Adapter x1.

33PIN FFC (same side contact) x1. RPi screws pack (2pcs) x1. PH2.0 20cm 8Pin x1.

The item "1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C" is in sale since Monday, July 29, 2019. This item is in the category "Business & Industrial\Electrical Equipment & Supplies\Electronic Components & Semiconductors\LEDs, LCDs & Display Modules\LCD Display Modules". The seller is "devkits" and is located in . This item can be shipped worldwide.


1872×1404 7.8inch E-Ink Display e-Paper HAT for Raspberry Pi USB/SPI/I80/I2C