1pcs 7inch HDMI LCD (H) 1024x600 IPS Capacitive Touch Screen Audio Output

1pcs 7inch HDMI LCD (H) 1024x600 IPS Capacitive Touch Screen Audio Output
1pcs 7inch HDMI LCD (H) 1024x600 IPS Capacitive Touch Screen Audio Output
1pcs 7inch HDMI LCD (H) 1024x600 IPS Capacitive Touch Screen Audio Output
1pcs 7inch HDMI LCD (H) 1024x600 IPS Capacitive Touch Screen Audio Output
1pcs 7inch HDMI LCD (H) 1024x600 IPS Capacitive Touch Screen Audio Output

1pcs 7inch HDMI LCD (H) 1024x600 IPS Capacitive Touch Screen Audio Output

1 x 7 Inch IPS Screen. 1 x ABS Case with Stander. 1 x HDMI Cable (30cm length). 1 x USB Cable (38cm length). The Raspberry Pi is not included.

There is a protective film on the screen, you can remove it before using. This is a universal IPS HDMI Display, 1024 × 600 resolution with tempered glass capacitive screen touch panel. Not only supports Raspberr Pi, but also supports Banana Pi, Beaglebone, other Mini PC ect. This screen can be used as a computer monitor, supports windows10.

1024x600 hardware resolution, onfigurable by software (up to 1920x1080). Toughened glass capacitive touch panel, 6H hardness. Supports popular mini PC such as Raspberry Pi, BB Black, Banana Pi.

Supports Raspbian, Ubuntu, WIN 10 IOT, single touch and driver free. Supports Desktop/Laptop, Supports Windows 10/8.1/8/7, five-points touch, and driver free. Multi languages OSD menu, for power management, brightness/contrast adjustment, etc. With high quality PC case, optional tilt angle: 30°/50°.

Raspberry Pi 3 Model B+, 3 Model B, 2B, B+. Power: Open or Close LCD display. Menu: Open OSD menu (It can also work as OK after entering the menu). Exit: it can also work as Return after entering the menu. You can use "Power" button to close LCD display for reducing consumption if it will be idle for a long time.

Open OSD menu by press button Menu, then use "OK button" and "Direction button" to change the configuration. Then use "Return button" to exit. 1/ Why the LCD doesn't work with my Raspbian? To use the LCD with the Raspberry Pi official image, driver should be installed first. Please refer to the user manual.

However, for the first testing, you may want to use our provided image directly. 2/ Why the LCD still doesn't work with the waveshare provided image? Make sure the hardware connection is correct and connects fine.

Make sure the image in TF card is burnt correctly. The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on. It is possible that the image was burnt incorrectly OR the TF card was in bad contact.

3/ Which power supply should I use? It is strongly recommended to use a stand-alone 5V/2A power adapter, because the PC's USB port might have not enough power to support the Pi and LCD. 1pcs ESP32 0.96 Inch Blue OLED Display SX1278 Bluetooth WIFI Kit 32 Module. 3.2 Nextion HMI Intelligent Smart USART Serial Touch Panel LCD Module Display.

5 Inch Nextion HMI LCD Display Screen Module for Arduino. 1.44 Colorful SPI TFT LCD Display ST7735 128X128 Replace Nokia 5110/3310 LCD.

1pcs 5mm 88 8x8 Full Colour RGB LED Dot Matrix Display Module Common Anode. 0.96 Inch 8Pin HD Color IPS Screen TFT LCD Display SPI ST7735 Module For Arduino.

SX1276 868MHz-915MHz LoRa Module ESP32 OLED Wifi Bluetooth IOT Development Board. ESP8266 WIFI Chip 0.91 inch OLED CP2014 32Mb Flash ESP 8266 Module for Arduino. The item "1pcs 7inch HDMI LCD (H) 1024x600 IPS Capacitive Touch Screen Audio Output" is in sale since Monday, November 5, 2018.

This item is in the category "Business & Industrial\Electrical Equipment & Supplies\Electronic Components & Semiconductors\LEDs, LCDs & Display Modules\LCD Display Modules". The seller is "cctv008008" and is located in .

This item can be shipped worldwide.


1pcs 7inch HDMI LCD (H) 1024x600 IPS Capacitive Touch Screen Audio Output