1200x825, 9.7inch E-Ink display HAT for Raspberry Pi, IT8951 controller, USB/SPI/I80/I2C interface. This is an E-Ink display HAT for Raspberry Pi, 9.7inch, 1200x825 resolution, with embedded controller IT8951, communicating via USB/SPI/I80/I2C interface.
Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on. No backlight, keeps displaying last content for a long time even when power down. Low power consumption, basically power is only required for refreshing. Compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+.
USB/SPI/I80/I2C interface, for connecting with host boards like Raspberry Pi/Nucleo, etc. Comes with development resources and manual (examples for Raspberry Pi/STM32). Outline dimension: 218.8mm × 156.425mm × 1.15mm. Display size: 202.8mm × 139.425mm.
Dot pitch: 0.169 × 0.169. Gray scale: 2-16 (1-4 bit). Total refresh power: 0.6Wtyp. Total standby power: 0.3Wtyp. SPI chip selection, low active.Busy status output, low active. E-Paper IT8951 Driver HAT Dimensions. 27.60 × 27.60.
48.0 × 33.0. 1.54inch e-Paper Module (B). 1.54inch e-Paper Module (C).27.51 × 27.51. 48.55 × 23.71. 65.0 × 30.2.
2.13inch e-Paper HAT (B). 2.13inch e-Paper HAT (C). 2.13inch e-Paper HAT (D). 59.2 × 184.108.40.206 × 38.19. 85.0 × 56.0. 2.7inch e-Paper HAT (B). 66.89 × 29.05. 89.5 × 38.0. 2.9inch e-Paper Module (B). 2.9inch e-Paper Module (C). 84.80 × 63.60. 103.0 × 78.5. 4.2inch e-Paper Module (B). 4.2inch e-Paper Module (C).
4.3inch e-Paper UART Module. 88.00 × 66.00. 118.0 × 75.0.
118.8 × 88.26. 125.4 × 99.5. 5.83inch e-Paper HAT (B). 5.83inch e-Paper HAT (C). 163.20 × 97.92.
170.2 × 111.2. 7.5inch e-Paper HAT (B). 7.5inch e-Paper HAT (C). 202.8 × 139.43. Standard Raspberry Pi header on module, allowed to be attached onto Pi directly, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+.E-Paper IT8951 Driver HAT x1. 9.7inch e-Paper Adapter x1.
33PIN FFC (same side contact) x1. RPi screws pack (2pcs) x1. PH2.0 20cm 8Pin x1. · We would be very appreciated if you could give us a good feedback if you're satisfied with our total service as well as our products, so that other customers can find out the products what exactly they want.
· If there have any problem of our products, pls contact with us asap, we will try our best to service for you. It's our pleasure to serve you!
The item "9.7inch E-Ink display Hat for Raspberry Pi Zero/Zero With3B/3B+ IT8951 controller" is in sale since Saturday, October 27, 2018. This item is in the category "Business & Industrial\Electrical Equipment & Supplies\Electronic Components & Semiconductors\LEDs, LCDs & Display Modules\LCD Display Modules".
The seller is "waveshare" and is located in . This item can be shipped worldwide.