Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951

Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951
Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951
Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951
Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951
Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951
Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951
Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951
Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951
Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951

Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951
1872×1404, 10.3inch flexible E-Ink display HAT for Raspberry Pi, IT8951 controller, USB/SPI/I80/I2C interface. This is a flexible E-Ink display HAT for Raspberry Pi, 10.3inch, 1872×1404 resolution, with embedded controller IT8951, communicating via USB/SPI/I80/I2C interface, supports partial refresh.

Compared with normal e-Paper panels, this flexible panel allows bending without being damaged, and it's thinner and lighter. Due to the advantages like low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as ebook reader, e-ink display, industrial instruments, and so on. Flexible e-Paper, the display section is bendable (DON'T bend the FPC section). No backlight, keeps displaying last content for a long time even when power down.

Low power consumption, basically power is only required for refreshing. Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards. USB/SPI/I80/I2C interface, for connecting with host boards like Raspberry Pi/Nucleo, etc. Comes with development resources and manual (examples for Raspberry Pi/STM32).

Outline dimension: 227.7mm × 165.8mm × 0.647mm. Display size: 209.664mm × 157.248mm.

Dot pitch: 0.112mm × 0.112mm. Gray scale: 2-16 (1-4 bit).

Total refresh power: 1.2Wtyp. Total standby power: 0.1Wtyp. SPI chip selection, low active.

Busy status output, low active. E-Paper IT8951 Driver HAT (B) Dimensions. 27.60 × 27.60. 48.0 × 33.0. 1.54inch e-Paper Module (B).

1.54inch e-Paper Module (C). 27.51 × 27.51. 48.55 × 23.71. 65.0 × 30.2. 2.13inch e-Paper HAT (B).

2.13inch e-Paper HAT (C). 2.13inch e-Paper HAT (D). 59.2 × 29.2. 57.29 × 38.19.

85.0 × 56.0. 2.7inch e-Paper HAT (B). 66.89 × 29.05.

89.5 × 38.0. 2.9inch e-Paper Module (B). 2.9inch e-Paper Module (C).

2.9inch e-Paper HAT (D). 66.90 × 29.06. 79.0 × 36.7. 84.80 × 63.60.

103.0 × 78.5. 4.2inch e-Paper Module (B).

4.2inch e-Paper Module (C). 4.3inch e-Paper UART Module. 88.00 × 66.00. 118.0 × 75.0.

118.8 × 88.26. 125.4 × 99.5. 5.83inch e-Paper HAT (B). 5.83inch e-Paper HAT (C).

122.4 × 90.6. 138.4 × 101.8. 163.20 × 97.92. 170.2 × 111.2.

7.5inch e-Paper HAT (B). 7.5inch e-Paper HAT (C). 158.18 × 118.64. 173.8 × 127.6.

202.8 × 139.43. 10.3inch e-Paper HAT (D). 209.66 × 157.25. 227.7 × 165.8. Standard Raspberry Pi header on module, allowed to be attached onto Pi directly, compatible with Raspberry Pi 40PIN GPIO extension header.

10.3inch e-Paper (D) x1. E-Paper IT8951 Driver HAT (B) x1. 10.3inch e-Paper Adapter x1.

33PIN FFC (same side contact) x1. RPi screws pack (2pcs) x1.

PH2.0 20cm 8Pin x1. The item "Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951" is in sale since Wednesday, July 10, 2019. This item is in the category "Business & Industrial\Electrical Equipment & Supplies\Electronic Components & Semiconductors\LEDs, LCDs & Display Modules\LCD Display Modules".

The seller is "waveshare" and is located in . This item can be shipped worldwide.


Waveshare 10.3inch flexible E-Ink display HAT for Raspberry Pi 1872×1404 IT8951